20A Brushed Electronic Speed Controller ₹439.00
Back to products
DC Motor Governor PWM Variable Speed Control Switch 6V-90V 15A ₹267.00
-17%
Click to enlarge

Brushless Motor Controller DC 12-36V 500W PWM Driver Board

  • Type of drive plate: JYQD_V6.3E2
  • Range of voltage: 12–36
  • Maximum current: 20 A
  • PWM frequency range for speed control: 1–20 KHz
  • Duty cycle: 0%–100%
  • 500W or less of drive power (associated working voltage)

IBOTS's 10th Anniversary Sale

Hurry and get discounts on all Raspberry Products up to 20%

IBOTS1000

₹1,151.00

Compare
Add to wishlist
  • Pick up from the IBOTS Store

Free

  • Delivery Charges: Tamil Nadu

₹75 for parcels below 1 Kg and ₹100 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹75

  • Delivery Charges: Other South India

₹125 for parcels below 1 Kg and ₹175 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹125

  • Delivery Charges: North India

₹250 for parcels below 1 Kg and ₹325 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹250

  • Courier delivery

Our courier will deliver to the specified address

2-3 Days

Rs. 99

  • Warranty 1 year

More details

  • Free Returns Policy

More details

Payment Methods:

1. Order the Product and Specify the Delivery Method

2. You Will Receive an Order Confirmation Message

3. Wait for Your Order to Arrive

4. Pick up Your Order at The Checkout Area

Description

Although it is not suitable for all 3-phase brushless sensor less motors directly, this Brushless Motor Controller DC 12-36V 500W PWM Driver Board is used for 3-phase brushless sensor less motors. Consumers can adjust the driver board’s resistance and capacitance to match the actual situation if the driving effect is not good (e.g., starting jitter, reversing, the motor no-load working current is too large, the speed is not stable, the efficiency is low, and it cannot start up with a load).

 

Generic Untitled 2

 

Specifications and Features :

  1. Protection: Overload protection, locked-rotor protection, over-current protection
  2. Analog voltage speed regulation: 0-5V
  3. Operating temperature: -40 ~ +85℃
  4. Drive power: ≤ 500W (related working voltage)
  5. Speed control function: voltage speed regulation or single-chip
  6. microcomputer control PWM speed regulation

Wiring Diagram

Pin Connection :
5V -Driver board internal output voltage
Signal – Motor speed pulse signal output port, 5V pulse signal.

Control port: 

Z/F– Rotating direction control ports. Connect “5V” high level or no connect is Forward direction, connect 0 V low level or connect to GND is a reverse direction.
VR -Speed control port. Analog voltage linear speed regulation 0.1v -5V, The input resistance is 20K Ohm, connect with GND when input PWM speed regulation, PWM frequency:1-20KHZ; Duty cycle 0-100%
GND—Used for Drive board internal control.

Power port : 

MA —-motor phase A
MB —- motor phase B
MC—- motor phase C
GND—-DC-
VCC—-DC +
3. Use shielded wires if the drivers’ board has more than 50 cm distance from the motor, otherwise, it may lead to abnormal driving, affecting the normal use.
4.Control port distance: 2.54mm,Power port distance: 3.96 mm
5. Pay attention to the insulation between the driver MOSFET and the heatsink or the installation plate.
Application notes:
  1. Confirm that the voltage and power parameters of the motor do not exceed the range of the driver board as specified.
  2. The JYQD-V6.3E2 driver board is a bare board without housing and a heatsink. If the power of the motor is below 60W, it does not need to add a heatsink, It only needs to ensure normal ventilation and wall insulation. If the power of the motor is more than 100W, it must add a heatsink.
  3. Please take note that the JYQD-V6.3E2 driver board has no anti-reverse connection protection, it will permanently damage the driver board if reversed polarity connection.
  4. The 5V output port on the driver board prohibits connecting an external device. It is only applicable to the external potentiometer and switch of the board for speed regulation and reversal.
  5. The “Signal” terminal on the JYQD-V6.3E2 driver board is the motor speed pulse output signal (push-pull output), and the maximum output current is less than 5mA.

Customer Reviews

0 reviews
0
0
0
0
0

Reviews

Clear filters

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.