12V 1 Channel Relay Module Original price was: ₹121.00.Current price is: ₹89.00.
Back to products
DC 12V Switch Delay-Relay Module with Adjustable Delay Time 0~25 Second Signal Triggering Switch Module Original price was: ₹198.00.Current price is: ₹149.00.
-17%
Click to enlarge

6-20V 1-Channel Power Relay Module with Adjustable Timing Cycle

  • Voltage range for operation: 6–20V
  • Time interval: constantly configurable, ranging from 0.1 s (minimum) to 999 min (maximum).
  • Isolation of an optocoupler.

Note:

  • Within India, 3 – 4 days lead time with 100% advance
  • For imports, 15 days lead time with 50% advance

IBOTS's 10th Anniversary Sale

Hurry and get discounts on all Raspberry Products up to 20%

IBOTS1000

Original price was: ₹410.00.Current price is: ₹342.00.

Available on backorder

Available on backorder

Compare
Add to wishlist
  • Pick up from the IBOTS Store

Free

  • Delivery Charges: Tamil Nadu

₹75 for parcels below 1 Kg and ₹100 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹75

  • Delivery Charges: Other South India

₹125 for parcels below 1 Kg and ₹175 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹125

  • Delivery Charges: North India

₹250 for parcels below 1 Kg and ₹325 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹250

  • Courier delivery

Our courier will deliver to the specified address

2-3 Days

Rs. 99

  • Warranty 1 year

More details

  • Free Returns Policy

More details

Payment Methods:

1. Order the Product and Specify the Delivery Method

2. You Will Receive an Order Confirmation Message

3. Wait for Your Order to Arrive

4. Pick up Your Order at The Checkout Area

Description

This is a 1-channel, 6-20V power relay module with a digital LED display and an adjustable timing cycle. The Home Automation Delay Timer Control Switch Module Timer Controller is the main use for it. The module can run between 6 and 20 volts, and it can accept a micro USB 5.0 volt power source.

Operation Mode:
  1. P1: Trigger signal, the relay is on “OP” time, and then disconnect; Within the “OP” time, proceed as follows:
  2. P1.1: the signal is triggered again, invalid
  3. P1.2: the signal is triggered again, re-clocking
  4. P1.3: Signal has triggered again, the relay is disconnected, stop the clock;
  5. P-2: Trigger signal, after the “CL” time is off, the “OP” time is on. When the timing is completed, the replay will be disconnected;
  6. P3.1: Trigger signal, after the “OP” time is on, the “CL” time is off, then cycle the above actions. If the trigger signal is within the loop, the relay will be disconnected and stop the clock. The number of cycles ( “LOP “) can be set.
  7. P3.2: No need to trigger the signal after powering up, the “OP” time is on, the “CL” time is off, then cycle the above actions; The number of cycles ( “LOP “) can be set.
  8. P-4: Signal holding function. If the signal is triggered, timing is cleared, the relay remains on; when the signal disappears, the relay will be off when the “OP” time is over; if another signal is triggered during timing, timing will be cleared.
How to choose the time interval:
parameter Introduction: OP power over time, turn off time CL, LOP cycle times (1-999 times, “—” is an unlimited cycle)
1. In the selection of parameter set interface mode, and press the STOP button to select the time.
(1)xxx. if the decimal point is in some place, the time interval is s-1 999 s
(2)xx. x is the decimal place is ten, the time interval is 0.1 s 99.9 s-
(3)x. x. x is the decimal point are all on, the time interval is 1 min-999 min
How to set the parameter:
  1. First, make sure relay operation mode
  2. According to the operating relay mode, the main interface (power module will flash current operating mode; standard mode P1.1, then come into the main interface); long press SET key two seconds and then choose and enter selection interface mode; by pressing UP, DOWN key to choose the mode setting  (P1.1 ~ P4)
  3. After selecting the mode, press short SET to set the corresponding parameter, then the parameter you want to set will flash (OP power in time; CL power off time; LOP cycle times, “—” is an unlimited cycle ); by UP, DOWN to set the parameter value, support long press (increase or decrease quickly) and press slightly (increase or decrease of 1 unit); after setting the parameter value by short press the STOP key to choosing decimal place; choose the time interval (corresponding time interval is 0.1 s-999 min); Short press SET to set the current mode next parameter, the process is the same as above
  4. After the setting mode parameter, press and hold the SET button then hold the current configuration mode will flash, then go back to the main interface; define success parameter main interface: when the relay does not work, it will show “000” (no decimal point); the operating state relay, the screen has a decimal point

 

 

Mode Select Interface:
press and hold the SET key to enter; after setting, long-press the SET button back on the main interface
Activate Relay Mode:
  1.  NO: PO in power over time, the relay can be connected
  2. OFF: relay is not allowed to connect, when in the off state
in short main interface press the STOP key to achieve turn ON and OFF, the current state will flash; then back to the main interface
(this function is a function of a sudden stop, 1 key to turn off the relay)
Sleep Mode:
C-P Sleep mode: within 5 minutes, no operation; nixie tube will close auto display, and a function program well
Note:
1. Press and hold the STOP button for 2 seconds can achieve change from C-P to O-d; the Current state will flash and then return to the main interface
2. The relay contact is passive and electricity production; 1 channel has the control function on / off

 Features:

  • Optocoupler Isolation: improve the anti-interference ability, after the parameter setting, it will be in memory forever.
  • Wide voltage power supply (6 ~ 20V), supports micro USB 5.0V power supply, easy to use.
  • The interface is clean, simple, powerful, and easy to understand, can meet almost all your needs.
  • With emergency stop function (“STOP” button) and reverse polarity protection which can avoid burning by reverse connection.
  • Adding sleeping mode, when the mode is enabled, if there is no operation within 5 minutes, the display will be turned off automatically, press any button will wake it up;
  • You can set different parameters of OP, CL, LOP, which are independent of each other and are stored separately;
  • All the parameter settings will be stored automatically when power is off.

Customer Reviews

0 reviews
0
0
0
0
0

Reviews

Clear filters

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.