FPV NEO-M8N GPS amp Compass Support DJI Naza M V1 & V2 Lite Flight Controller

M8 engine with 72 channels, receiver type.
Tracking and navigation sensitivity: -167 dBm.
TCXO oscillator (NEO-M8N/Q).
RTC crystal Integrated.
Minimum noise level (NEO-M8N/Q).
Active CW detection and elimination for anti-jamming. Extra.
The Neo-M8N/Q is an onboard SAW bandpass filter.
Flash (NEO-M8N) or Memory ROM (NEO-M8M/Q).
Both active and passive antennas are supported.

Note:

Within India, 3 – 4 days lead time with 100% advance

For imports, 15 days lead time with 50% advance

IBOTS's 10th Anniversary Sale

Hurry and get discounts on all Raspberry Products up to 20%

IBOTS1000

2,650.00

Available on backorder

Available on backorder

  • Pick up from the IBOTS Store

Free

  • Delivery Charges: Tamil Nadu

₹75 for parcels below 1 Kg and ₹100 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹75

  • Delivery Charges: Other South India

₹125 for parcels below 1 Kg and ₹175 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹125

  • Delivery Charges: North India

₹250 for parcels below 1 Kg and ₹325 for parcels weighing between 1 Kg to 2 Kg.

2-3 Days

₹250

  • Courier delivery

Our courier will deliver to the specified address

2-3 Days

Rs. 99

  • Warranty 1 year
  • Free Returns Policy

Payment Methods:

1. Order the Product and Specify the Delivery Method

2. You Will Receive an Order Confirmation Message

3. Wait for Your Order to Arrive

4. Pick up Your Order at The Checkout Area

Description

Supports DJI Naza M V1 & V2 Lite Flight Controllers with FPV NEO-M8N GPS amp Compass. The NEO-M8N is a new generation GPS device that boasts low power consumption and high precision. Its ultimate accuracy is 0.6 metres, or about 0.9 metres, which is greater than the 1.4-1.6 metres accuracy of the NEO-7N, the previous generation device. It also supports more protocols, including GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode.

32-bit processing, significantly better than an 8-bit CPU, is compatible with the NAZA M V1 & V2 flight controller. Please pay attention to the GPS’s arrow, which represents a flyer’s head. Comparable GPS calibration and application. includes a 30-cm soft silicone gel cable. A surface was covered with black rubber to make it softer. To lessen signal interference from other electrical devices, a metal foil label has been placed on the bottom of the GPS (Notice: black cable= GND, white cable= TX, yellow cable= RX, red cable= 5V, 3.3-7.5V is OK).

Note: To calibrate the electronic compass is the first important thing when received your GPS.

Calibration Method:

Connect the GPS to the flight controller, turn on the radio control model switch seven or ten times, and watch as the LED light glows orange. After turning the flyer one circle horizontally, the LED light turns green. A flyer’s head flashed on when it was made to turn one circle and point downward.

Features:

Support GNSS Online Assistance Now.
HelpNow GNSS Offline for a maximum of 35 days3.
Autonomous AssistNow (up to 6 days).
3GPP and OMA SUPL compatible.
TCXO oscillator (NEO-M8N/Q).
Neo-M8M crystal.
RTC crystal Integrated.
On-chip LNA noise figure (NEO-M8M). Additional LNA for.
Minimum noise level (NEO-M8N/Q).
Active CW detection and elimination for anti-jamming.

The Neo-M8N/Q is an onboard SAW bandpass filter.
Flash (NEO-M8N) or Memory ROM (NEO-M8M/Q).
Both active and passive antennas are supported.
Odometer distance travelled.
Data-logger For time, location, and velocity (NEO-M8N).
compatible with RoHS (lead-free).
Produced in ISO/TS 16949 certified production facilities, after thorough testing.
uses M8 chips that meet AEC-Q100 qualification standards.
1.65 V to 3.6 V is the supply voltage (NEO-M8M).
4 23 mA of power consumption at 3.0 V (continuous).

3.0 V at 5 mA in Power Save Mode.
(1 Hz, exclusively in GPS mode).
M8 Concurrent GNSS LCC Module, NEO-M8N-0.
Flash, SAW, LNA, TCXO.
Temporal pulse Adjustable from 0.25 Hz to 10 MHz.
Compared to the 8-bit CPU, the 32-bit processor is significantly superior and compatible with the DJI NAZA LITE V1 & V2 flight controller.
Please pay attention to the GPS’s arrow, which represents the flyer’s head.
Comparable setup and application with DJI GPS.
includes a 30-cm soft silicone gel cable.
Black rubber was applied to the surface to add suppleness.
(Note: 3.3-7.5V is OK; black cable = GND, white cable = TX, yellow cable = RX, red cable = 5V).
The GPS features a metal foil label attached to its bottom to lessen signal interference from other electrical devices.

Customer Reviews

0 reviews
0
0
0
0
0

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.