Showing 733–744 of 2389 results
Shop
CT14 Bluetooth 4.2 F Class 5W+5W Stereo Audio Amplifier Module with Onboard Micro-USB battery Charging
- Bluetooth version: 4.2
- Supply current: 1A
- Power supply voltage: 5V
- Max. Audio Output Power: 10W
- No soldering Required on Module
Cyclone 35A 2-6S Blheli_S DSHOT600 OPTO Brushless ESC for RC Drone FPV Racing
Up to 48 KHz of programmable PWM frequency
Power source: 7.4–16.8V, 2–6S
Constant current: 25 A
Current at burst: 35A (5S)
Auto-timing for increased dependability and efficiency
Cyclone 45A BLHeil_S ESC
Product: BLHeil_S ESC Cyclone 45A
Voltage: Suitable for 2–6 S power sources
Current in use: 35A
Supported Dshot 125, 300, and 600 procedures
Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
The potentiometer (10K Ohm) that comes with the box can be used to adjust the speed thanks to the MD10-POT control circuit. Analogue voltage from an external controller is not compatible with it. Two functions of the 3-way rocker switch are direction control and start/stop.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Cytron 20Amp 6V-30V DC Motor Driver MD20A
- Control in both directions for a single brushed DC motor.
- Working Voltage: DC 6–30 V
- Maximum Motor Current: 60A at peak, 20A continuously
- Buttons for rapid experimentation.
- For motor output state, use LEDs.
- Active current limitation combined with overcurrent protection.
- Protection against temperature.
- Shutdown due to low voltage.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Cytron Arduino PS2 Shield
- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
Cytron Dual channel 10A Motor Driver UNO Robot Controller
- Upon board 1A (uppermost) voltage regulator for 5 volts.
- 500mA maximum onboard Voltage regulator at 3.3V.
- 3.3V compatible inputs and 0–5V digital outputs.
- Six PWM outputs and 14 digital I/O pins.(A motor driver uses four pins.)
- Six analogue inputs (digital I/O is also possible).
- Maximum current of 30 amps peak and 10 amps continuous.
- 6-pin header for ISPs.
- 32k RAM for Flash.
- 16 MHz is the clock speed.
- R3 Shield Compatible.
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
Cytron G15 Shield
-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
Cytron Maker Pi Pico Base (without Pico)
- Designed for Raspberry Pi Pico.
- Offers three programmable push button and six Grove ports.
- Comes with a comprehensive pinout diagram.
- Access to all Raspberry Pi Pico’s pins.
- Doesn’t require soldering.
Load more products
Loading...