Showing 745–756 of 2404 results
Shop
Cytron Dual channel 10A Motor Driver UNO Robot Controller
- Upon board 1A (uppermost) voltage regulator for 5 volts.
- 500mA maximum onboard Voltage regulator at 3.3V.
- 3.3V compatible inputs and 0–5V digital outputs.
- Six PWM outputs and 14 digital I/O pins.(A motor driver uses four pins.)
- Six analogue inputs (digital I/O is also possible).
- Maximum current of 30 amps peak and 10 amps continuous.
- 6-pin header for ISPs.
- 32k RAM for Flash.
- 16 MHz is the clock speed.
- R3 Shield Compatible.
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
Cytron G15 Shield
-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
Cytron Maker Pi Pico Base (without Pico)
- Designed for Raspberry Pi Pico.
- Offers three programmable push button and six Grove ports.
- Comes with a comprehensive pinout diagram.
- Access to all Raspberry Pi Pico’s pins.
- Doesn’t require soldering.
Cytron Maker UNO Microcontroller Board- Arduino UNO Compatible Module
- SMD ATmega328P microcontroller(the same microcontroller on Arduino UNO) with Optiboot (UNO) Bootloader
- USB Programming facilitated by the CH340
- Input voltage: USB 5V, from computer, power bank or standard USB adapter
- Piezo buzzer that will act as simple audio output
- 500mA (maximum) 3.3V voltage regulator
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP 6-pin Header.
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
Package Includes:
1 x Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
Tutorials:
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
- Low voltage indication for batteries.
- Overvoltage warning indicator for batteries.
- Thermal defence.
- Preservation of the current limit.
- Dual brushed DC motor with bidirectional control.
- Support voltage range for motors: 7V to 35VDC.
- Dimensions: L x W x H = 103 x 97 x 40 mm.
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
- One-power operation
- With dual channels, two brush motors can be driven separately or in combination.
- Encouragement PWM mode with Signed magnitude and Locked Anti-phase.
- Every channel has two manual/test buttons.
- Each channel has two LEDs for the output indicator.
- Power, RUN status (Left and Right), and error indicator LEDs
- To restart the MCU after switching operation modes, press the on-board reset button.
- Operating modes include packetized UART, analogue, PWM, RC (RC servo signal), and simplified UART.
D1 Mini V2 NodeMcu 4M Bytes Lua WIFI Internet Of Things Development Board Based ESP8266
- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
D2-6 Bluetooth Remote Control Intelligent Car 51 MCU DIY Kit
D80SH-12 8025 12V Cooling Fan Power Supply Cabinet
- Ideally suited for the extruder
- Silent Performance
- Extremely low usage of current
- Simple to connect to and install.
Daly Smart BMS Bluetooth Module
- User-Friendly Interface
- Compatibility
- Energy Efficient
- USB: Micro USB
Load more products
Loading...