Showing 841–852 of 2404 results
Shop
Digi XBee3 2.4GHz ZB3.0 RP-SMA Female Antenna
- Serial Data Interface: Uart, Spi, I2c.
- Onboard Connector: RP-SMA Female.
- Configuration Method: API Or At Commands, Local Or Over-the-air
- Frequency Band: ISM 2.4 GHz
- Interference: Immunity Dsss (Direct Sequence Spread Spectrum)
- Adc Inputs: (4) 10-bit Adc Inputs
- Digital I/o: 15.
DigiKey Zigbee 3.0 Module?XB3-24Z8CM –
- Supports Zigbee 3.0 Protocol
- Compact Size and Low-Power Module
- Comes in SMD Package
- Easy-to-Add Connectivity in a Compact Space
Digispark ATTINY85 Mini USB Development Board
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 512 Bytes In-System Programmable EEPROM
- 512 Bytes Internal SRAM
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- 4 Single Ended Channels
- Two Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
Digital Display for HC-SR04 Ultrasonic Distance Measurement Control Board
- High-performance STM8S103 microprocessor onboard with digital tube display and valid measurement 3-400 cm is the distance.
- Unit of Display: cm
- 2.54mm White Socket: 5V power interface; Maximum Input Voltage: 5VDC.
Digital Multi Servo Tester ESC RC Consistency CCPM Master Speed Control
- Operating Voltage: DC 4.8-6V
- Offer 3 modes to check servos or ESC
- The Manual Mode allows you to turn the knob to different speeds and check the reaction time
- The Neutral mode makes the servo go back to the neutral point
- The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible
- Connect to up to 3 servos simultaneously
Digital Voltmeter (0-100V) and Ammeter (10 A) Dual Led Voltage Current Measurement Module
Input Voltage – 4.5V to 30V DC
Input Current – <= 20mA
Display Color – Red (Voltage) , Blue (Current)
Measuring Voltage Range – 0V to 100V DC
Measuring Currrent Range – 0A to 10A
Measurement Accuracy – 1%
Minimum Voltage Resolution – 0.1V
Minimum Current Resolution – 0.01A
Size – 48x29x21mm
DIP 3 Color LED Module
- The use of plug-in full-color LED.
- RGB trichromatic limiting resistor to prevent burnout.
- Through the PWM adjusting, three primary colors can be mixed to obtain different colors.
- With a variety of single-chip interface.
- The working voltage: 5V.
- LED drive mode: common cathode driver
Direct V6 Short Distance 1.75 3D Hotend Heatsink
- Adaptable to nozzles of various diameters
- Simple to set up and operate
- High-Temperature Operation
- Inner diameter: 4.7 mm (End-2) and about 1.6 mm (End-1).
DIY Acrylic case for Class D Power Amplifier
- Product: DIY Acrylic case
- Material: Acrylic
- Excellent clarity.
- Lightweight.
- Good impact resistance
DIY D2-1 Intelligent Line Follower/Tracing Car Kit
- Easy to Assemble
- Operating Voltage: 3V
DIY D2-2 Intelligent Line follower/Tracking Smart Car Kit
DIY D2-5 Intelligent Tracking Line Car Kit
- Easy to Assemble
- Operating Voltage: 3V
Load more products
Loading...