Showing 853–864 of 2380 results
Shop
Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module
- Input voltage(V): 6 – 27.
- Maximum current(A): 43.
- Input level(V): 3.3 – 5.
- Duty cycle: 0 – 100%.
- Path resistance: 16 mΩ at 25°C.
- Low quiescent current: 7 µA at 25°C.
Double Fans Radiator for Raspberry Pi 3B+/4B
- Type: Raspberry 4B Aluminum Alloy Metal Heat Sink
- Material: Black Aluminum Alloy Metal
- Compatible For:Raspberry all Variant of PI 3B and 4B Model B
- Open case design with Daul Fans for Fast Heat dissipation.
- All ports and slots of the case can match with Raspberry Pi 4 Model B perfectly
Double USB Type A Female Solder Jacks Connector PCB Socket (Pack of 5)
- Two ports stacked one on another
- Durable.
- Robust.
- Supports USB 2.0 hardware.
Drone 20A 2-4S Mini BLHeli-S OPTO ESC for FPV Race RC Helicopter
20A model BLHeli-S Appropriate Lipo for OPTO ESC 2 to 4 S batteries
Current constant: 20A
Peak Current: 25 A (10 s)
DS18B20 Module for D1 MINI Temperature Measurement Sensor Module
- Supporting the D1 MINI
- The Arduino Compatible, Using Arduino IDE Programming
- 11 the XI/O Pins
- 1 XADC Pin (0-3.3 – V)
- Support the OTA online
DS18B20 Water Proof Temperature Probe – Black (1m) Original Chip
- A temperature sensor chip (DS18B20) by fresh original installation import.
- Rust is prevented by the waterproof, moisture-proof stainless steel tube encapsulation.
- Lead length of 100 mm, stainless steel shell (6 * 45 mm) (shielding wire) employ stability
- 3.0 V to 5.5 V power supply
- Broad temperature range: -55 °C to +125 °C
- Exclusive single bus design without external components.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
DSM501A PM2.5 Dust Sensor Module for Arduino, Air-Conditioners
Using a heating automated suction device and adjustable resistance, the DSM501A PM2.5 Dust Sensor Module can detect household dust, pollen, tobacco smoke, and house dust. To determine the precise number of particles per unit volume, the same particle counter technique is used as the basis.
DSO138 2.4″ TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered
- This kit has a 2.4-inch colour TFT display screen and an ARM Cortex-M3 processor (STM32F103C8).
- vertical displacement that is movable and comes with instructions.
- It is simple to catch the moment waveform with the automatic, regular, and one-shot modes.
- A rising or falling edge trigger is available.
- Previous trigger waveform that can be observed (negative delay).
- Waveform display is capable of freezing at any moment (the HOLD function).
- Maximum Sample Rate in Real Time: 1 msps
- 12 bits of accuracy and 1024 bytes of sampling buffer depth
- Bandwidth in analogue: 0-200 KHz
DSP PLL 87-108Mhz Stereo FM Transmitter Module Digital LCD Display Wireless Microphone Board Multi-function Frequency Modulation
- Output power: 500mW (drive headphones), 3W (drive speakers)
- Frequency range: 50Hz-18KHz
- Close campus radio 87.0MHz-108.0MHz
- Open campus radio 76.0MHz-108.0MHz
- Equivalent noise: ≥30dB
- Channel: speaker (mono), headphone (stereo)
- Maximum volume 400mA
DType Big 4Pin to 6Pin Power Lines About 15CM
- Product: Large D-type Power Lines with 4 to 6 Pins
- Power cord is the connecting wire.
- Copper is the wire material.
- Use to link computers and graphic cards: Power cable
- Shade: Black
Dual Display 10A Power Adjustable Step-Down Constant-Voltage Constant-Current Power Module (With Case)
- Voltage input: DC 10V–32V
- Voltage of Output: DC 10V–60V
- Maximum Input Current: 16A
- Range of Operation Temperature: -40 to 85 degrees
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- Four-level LED light display power, intelligent automated shutdown when not in use.
- Two USB ports for output.
- MicroUSB port for input (Andro).
- USB output port available.
- 5V1A / 5V2A are the output parameters.
Load more products
Loading...