Showing 865–876 of 2404 results
Shop
DS18B20 Module for D1 MINI Temperature Measurement Sensor Module
- Supporting the D1 MINI
- The Arduino Compatible, Using Arduino IDE Programming
- 11 the XI/O Pins
- 1 XADC Pin (0-3.3 – V)
- Support the OTA online
DS18B20 Water Proof Temperature Probe – Black (1m) Original Chip
- A temperature sensor chip (DS18B20) by fresh original installation import.
- Rust is prevented by the waterproof, moisture-proof stainless steel tube encapsulation.
- Lead length of 100 mm, stainless steel shell (6 * 45 mm) (shielding wire) employ stability
- 3.0 V to 5.5 V power supply
- Broad temperature range: -55 °C to +125 °C
- Exclusive single bus design without external components.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
DSM501A PM2.5 Dust Sensor Module for Arduino, Air-Conditioners
Using a heating automated suction device and adjustable resistance, the DSM501A PM2.5 Dust Sensor Module can detect household dust, pollen, tobacco smoke, and house dust. To determine the precise number of particles per unit volume, the same particle counter technique is used as the basis.
DSO138 2.4″ TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered
- This kit has a 2.4-inch colour TFT display screen and an ARM Cortex-M3 processor (STM32F103C8).
- vertical displacement that is movable and comes with instructions.
- It is simple to catch the moment waveform with the automatic, regular, and one-shot modes.
- A rising or falling edge trigger is available.
- Previous trigger waveform that can be observed (negative delay).
- Waveform display is capable of freezing at any moment (the HOLD function).
- Maximum Sample Rate in Real Time: 1 msps
- 12 bits of accuracy and 1024 bytes of sampling buffer depth
- Bandwidth in analogue: 0-200 KHz
DSP PLL 87-108Mhz Stereo FM Transmitter Module Digital LCD Display Wireless Microphone Board Multi-function Frequency Modulation
- Output power: 500mW (drive headphones), 3W (drive speakers)
- Frequency range: 50Hz-18KHz
- Close campus radio 87.0MHz-108.0MHz
- Open campus radio 76.0MHz-108.0MHz
- Equivalent noise: ≥30dB
- Channel: speaker (mono), headphone (stereo)
- Maximum volume 400mA
DType Big 4Pin to 6Pin Power Lines About 15CM
- Product: Large D-type Power Lines with 4 to 6 Pins
- Power cord is the connecting wire.
- Copper is the wire material.
- Use to link computers and graphic cards: Power cable
- Shade: Black
Dual Display 10A Power Adjustable Step-Down Constant-Voltage Constant-Current Power Module (With Case)
- Voltage input: DC 10V–32V
- Voltage of Output: DC 10V–60V
- Maximum Input Current: 16A
- Range of Operation Temperature: -40 to 85 degrees
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- Four-level LED light display power, intelligent automated shutdown when not in use.
- Two USB ports for output.
- MicroUSB port for input (Andro).
- USB output port available.
- 5V1A / 5V2A are the output parameters.
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
Dual USB Output 9V / 12V / 24V / 36V Car Charger Switch 5V DC-DC Power Supply Module 3A Buck Regulator
- Input : 6V-40V
- Output : 5V / 3A (MAX)
- Efficiency : 92% (MAX)
- Switching frequency : 150KHZ
- High efficiency and low ripple.
- With USB power indicator light.
- Maximum output 3A (at the same time with two mobile phones).
Dual USB Output 9V/12V/24V to 5V 3A DC-DC Car Charging Voltage-Stabilizer Module
- Range of input voltage: 6-26V
- 5.2V is the output voltage (take into account the loss in the charge line; the load side is approximately 5V).
- Output current: 3A (the stable output current is 2A in the absence of a heat sink device).
- Two devices can be charged simultaneously using two output ports.
Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board compatible with Arduino
- Microcontroller: AT91SAM3X8E
- Operating Voltage: 3.3V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-16V
- Digital I/O Pins: 54 (of which 12 provide PWM output)
- Analog Input Pins: 12
- Analog Outputs Pins: 2 (DAC)
- A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
- CPU clock at 84Mhz
- 96KBytes of SRAM
Load more products
Loading...