Showing 1501–1512 of 2404 results
Shop
NEMA34 46 kg-cm Stepper Motor – Keyway Type Shaft
- Step Angle Step Angle: 1.8 °
- Current: 4 A/Phase
- Holding Torque: 460 N-cm
- Lead Wires: 4
- Shaft diameter: 14 mm
NEMA34 87 kg-cm Stepper Motor – Keyway Type Shaft
- Step Angle Step Angle: 1.8 °
- Current: 5 A/Phase
- Holding Torque: 870 N-cm
- Lead Wires: 4
- Shaft diameter: 14 mm
NEO 7M GPS With Compass for APM 2.6/2.8 and Pixhawk 2.4.6/2.4.8
161 dBm is the tracking sensitivity.
148 dBm is the capture sensitivity.
average cold start time of 38 s
Warm start time on average: 35 sec
average hot start time: 1 second
Average capture time: 0.1s
NEO-M8N GPS with Compass for Pixhawk with extra connector for APM
Prepared to Connect with a 6-pin Connector to PIXHAWK FC Galileo-ready E1B/C (NEO-M8N) receiver type 72-channel M8 engine attached
Navigation update rate (1) GNSS alone: up to 18 Hz
Purchasing Cold starts: 26 seconds Compass on board
Note:
Within India, 3 – 4 days lead time with 100% advance
For imports, 15 days lead time with 50% advance
New ESC USB Linker Programmer For Simonk BLHeli Firmware SN/BL/16A/20A/30A/40A
Straight plug architecture
most USB ports and USB extension cables are compatible
Design with little power usage
Upon board 3 pin servo connector that can be used as a servo or C2 Connection; 2 x 3 pin AVR ISP port
Supports BLHELI and SIMONK ESC; compatible with KKflashtool
Compatible with RapidFlash and KKflashtool
Note:
Within India, 3 – 4 days lead time with 100% advance
For imports, 15 days lead time with 50% advance
New High Quality Black ABS Case for Raspberry Pi 3/3+ with Cooling FAN Vent
- This simple case provides tough protection for your raspberry pi along with access to ports
- High Quality two-piece injection-molded ABS enclosure
- Click together design, no screws, standoffs or elastic bands required
- It is easy to use. You just need to click them together after you fix your pi board on it with screws.
New High Quality Transparent ABS Case for Raspberry Pi 3/3+ with Slot for Cooling Fan & GPIO
- This simple case provides tough protection for your raspberry pi along with access to ports
- High Quality two-piece injection-molded ABS enclosure
- Click together design, no screws, standoffs or elastic bands required
- It is easy to use. You just need to click them together after you fix your pi board on it with screws.
- 4 x Non-slip Silicone Gaskets provided, which can be stuck to the bottom four corners of the box, to prevent it from slipping when placed on a surface.
New V6 Heating Block Compatible with PT100 Sensor
- Accept M6 Nozzle with Acceptance
- 6 mm is the heater tube’s inner hole.
- Thermocouple or thermostat inner hole: 3 mm
- Set screw inner hole: M3
- Dimensions: 23 x 16 x 11.5 mm (L x W x H).
Nextion BASIC NX3224T024 2.4″ TFT ManMachine Interface HMI kernel LCD Touch Display
A smooth Human Machine Interface (HMI) solution, Nextion offers a control and visualisation interface that lets a person interact with a machine, process, application, or appliance. Nextion is mostly used in the consumer electronics and Internet of things (IoT) domains.
Nextion BASIC NX8048T070 7.0″ HMI TFT LCD Touch Display
- No of Model: NX8048T070
- VDC (operational voltage): 4.75 to 7.
- Maximum Current Used (mA): 510
- Type of Display:011R (Resistive Touchscreen)
- Type of Touch: Resistant
- 65K (65536) colours
- Temperature Range for Operation (°C): -20 to 70
- Operating Humidity: 10% to 90% R.H.
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
Nextion Enhanced NX8048K070 7.0” HMI Touch Display
- Allows for integrated RTC
- Maximum 32G Micro TF/SD card (FAT32 file format) is supported via the GPIO SD Card interface.
- 65K (65536) colours in total
- Dimensions: 800 x 480 pixels
Nextion Intelligent NX4827P043-011C 4.3″ HMI Capacitive Touch Display
- Memory in Flash: 128 MB
- 1024-bit EEPROM
- XH2.54 with a 4-pin TTL serial interface (+5V, TX, RX, and GND)
- 1.25T-2-2A Audio port for connecting an external speaker
- 8 Digital extended GPIO (IO6-IO7 supports PWM, IO0-IO7 supports input, output, and component binding event)
- Integrated RTC assistance
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance