Showing 2581–2592 of 4062 results
Shop
MQ-131 Ozone Gas Detector Sensor Module
- Fast response characteristics
- Mounting holes to facilitate fixed installation
- The probe can plug design for easy testing.
- Signal light indicates the output
- Dual signal output (analog output, and TTL-level output)
- TTL output valid signal is low; (low output signal light, can be accessed by the microcontroller IO port)
MQ-136-Hydrogen Sulfide Gas Sensor
- Dual signal output (analog output and TTL level output)
- The TTL output effective signal is low.
- Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage.
- Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke.
- with long service life and reliable stability
- fast response recovery characteristics
MQ-137 Ammonia Gas NH3 Sensor Module
- Wide detecting scope
- Fast response (less than 1s)
- High sensitivity( 3%)
- the circuit voltage: DC5V
- Stable and long life
- Operating Voltage is +5V
- Detect/Measure NH3, Ammonia
MQ-3 Alcohol Detector Gas Sensor Module
- Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off).
- Current Consumption: 150mA.
- DO output: 0.1 and 5V.
- AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detecting Concentration: 0.05-10mg/L Alcohol.
MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module
MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module
- Detecting range: 300~10000ppm
- Signal output indicator.
- Dual Signal output (analog output and TTL output).
- The TTL output signal is low level, allows us to connect with SCM directly.
- Analog output 0~5V voltage.
- Quick response and recovery. FOR BULK B2B ENQUIRIES MAIL US @ibots.in
MQ-7 CO Carbon Monoxide Coal Gas Sensor Module
- DC 5 V is the operating voltage.
- The analogue output voltage increases with increasing concentration.
- The more sensitive carbon monoxide detection.
- With dependable stability and an extended service life.
- Quick reaction times and recuperation traits.
- 10–1000 parts per millilitre.
MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module
- Good sensitivity to CO/Combustible Gas
- High sensitivity to Methane, Propane, and CO
- Long life and low cost
- Simple drive circuit
- Input voltage: DC 5±0.2V
- Current Consumption: 150mA
MQ135 – Air Quality Gas Detector Sensor
Features :
- Sensitivity to Ammonia, Sulphide, and Benzene steam
- With signal output instructions
- The TTL output signal is a low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Color is showing pictures.
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Output voltage boosts along with the concentration of the measured gases increases.
MQ2 Smoke LPG Butane Gas Sensor Module
- Operating Voltage is 5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO and even methane
- Can be used as a Digital or analog sensor
- The Sensitivity of Digital pin can be varied using the potentiometer
- Long life and low cost
- Simple drive circuit
MS 4525DO Air Speed Sensor And Pitot Tube Set for Pixhawk
MS 4525DO is the model.
Measurement Range: 223 mph/360 km/h at 1 psi and 100 m/s.
Resolution: 0.84 Pa
MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
- It’s efficient up to 93%
- It can source a good amount of current
- The maximum output current: 2A
- Input voltage: 2V-24V DC
- The maximum output voltage: 5V-28V DC
MT76813DBI ESP8266 Serial WIFI wireless Gain Antenna
- Radome material: polyurethane
- Flexible cable
- Stable signal
- Best for indoor applications.
- Connector: IPX female to SMA-KY
- Frequency (Hz): 900/1800
- Gain: <3 dB
- VSWR: <1.5
Load more products
Loading...