Showing 373–384 of 511 results
Shop
Obstacle Avoiding Robot Using Arduino Uno & L298N – Assembled Robot
Official Micro-HDMI (Male) to Standard HDMI (Male) Black Cable-2m for Raspberry Pi
- Fully compatible with High-Speed HDMI with Ethernet specification (Version 1.4).
- A superb cable with excellent audio-visual transfer properties that deliver signal without compromising purity and balance.
- Nickel-plated connectors for highest signal transfer rate and resistance in corrosion.
- A large gauge PVC jacket provides maximum shielding against wear and tear and extreme temperatures.
- Reinforced quad-layer braided shielding and Mylar-foil shielding provides utmost protection against RF and EM interference.
- Supports 480i, 480p, 720p, 1080i, 1080p, 1440p and 4K@60p resolution HDMI plug to HDMI plug leads
- Compatible with Raspberry Pi 4 Model B and all previous Raspberry Pi models.
Official Micro-HDMI (Male) to Standard HDMI (Male) Cable for Raspberry Pi
- Fully compatible with High-Speed HDMI with Ethernet specification (Version 1.4).
- A superb cable with excellent audio-visual transfer properties that deliver signal without compromising purity and balance.
- Nickel-plated connectors for highest signal transfer rate and resistance in corrosion.
- Large gauge PVC jacket provides maximum shielding against wear and tear and extreme temperatures.
- Compatible with Raspberry Pi 4 Model B and all previous Raspberry Pi models.
Official Raspberry Pi 4 Case-Red-White
- Easy two-piece installation design
- Hole for mounting the pi inside the case
- Rubber pad grip at the bottom
- Precise access to all port and status LEDs with Symbols
- Raspberry LOGO on Top
Official Raspberry Pi 5 Case Red-White
- Easy three-piece installation design
- ABS plastic Material
- Holes for mounting the pi inside the case
- Rubber pad grip at the bottom
- Enhance thermal management
Official Raspberry PI Zero W Case
- Good Quality ABS Material.
- GPIO access (allowing access to the pins for HATs, pHATs and/or jumper cables).
- Camera Mount & Lens hole.
- Accurate fittings.
Original Arduino Uno Rev3 A000066
- Manufacturer: Arduino Officials
- Micro-controller : ATmega328P.
- Operating Voltage: 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins: 14 (of which 6 provide PWM output).
- Analog Input Pins: 6.
Panasonic CR1632 3V Lithium Coin Battery
- 3V is a high and stable voltage.
- A complete range suitable for numerous applications
- No additional mercury
- Beneficial in a broad temperature range (-30°C to +60°C)
- Extremely high power to weight ratio
- Long-lasting existence.
Panasonic CR2032 3V Lithium Coin Battery-2Pcs.
- 3V is a high and stable voltage.
- A complete range suitable for numerous applications
- No additional mercury
- Beneficial in a broad temperature range (-30°C to +60°C)
- Extremely high power to weight ratio
- Material containing manganese dioxide
- large capacity and extended lifespan.
- Superior storability and a low rate of self-degradation
Panasonic CR2450 3V Lithium Coin Battery
- High and Stable voltage (3V)
- A full line up for use in a wide variety of applications
- No mercury added
- Useful in a wide range of temperatures (-30°C to +60°C)
- Very high weight-to-power ratio
- Long Lasting life.
PDB181-K220K-104B-Rotary Potentiometer
- Resistance of Track: 100 kohm
- Number of Turns: One
- Linear Track Taper
- 200mW of power
- Tolerance to Resistance: +/- 20%
Ph Sensor module
This PH rod is designed on ATMEGA8 Ic .
On board LDR for light value, Thermister fortemperature value.
It gives Serial data at its Tx pin
PH value W: depth of rod immersed L : light value T temperature value
PH W L T
Load more products
Loading...







Motors