Showing 469–480 of 4090 results
Shop
3S 12V 25A 18650 Lithium Battery Protection Board
- Current for operation: 0–25A.
- Current at instantaneous: 35–40A.
- Conditions for storage: -40 to +80°C.
- Current at quiescence: < 30 uA.
- Current balance: between 40 and 50 mA.
- Extended useful life: over 30,000 hours.
3V-12V Big Buzzer with Wire
- Diameter : 30mm
- Length : 15mm
- Input Voltage : 3V-12V
4 Channel 12V Relay Module Solid State High Level SSR DC Control 250V 2A with Resistive
- Number of Part: G3MB-202P
- Energy source: 12 VDC/160 mA
- Voltage at Trigger (VDC): 6–12
- VAC switching voltage: 240@2A
- Phototriac isolation
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
4 Channel Infrared Tracing Module
- Working voltage (V): 3.3 ~ 5
- Working current (A): Above 1A
- Operating Temperature (℃): -10 ~ +50
- Mounting hole: M3
- Detection range: 1mm ~ 20 cm adjustable.
4 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting
4 Channel Wireless Four Button RF Remote Control Transceiver Module
- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- Transmitter Radiated power: 10mW at 12V.
- Transmission distance (m): 3 to 5.
4 Channel Wireless Four Button RF Remote Control Transceiver Module (Mode: Non Locking)
- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- Transmitter Radiated power: 10mW at 12V.
4 in 1 Soil PH Meter Soil Tester PH Moisture Meter Temperature Sunlight Measurement Analysis Acidity Alkali(Without Battery)
- On-screen Battery Level Indicator with four distinct readings on a single screen
- Unit change switch
- Using a 200 mm probe, determine the root level
- Plug and play, portable, yellow backlit screen, power sleep mode for extended battery life
4 Pin Battery/Motor Connector
4 Pin battery/motor connector set. 6.3mm terminals for 16 through 14 gauge wire. Includes matching 8 piece pin and socket terminal set. Commonly used for throttle, brake lever, power switch, and speed controller connections.
4 Pin JST XH 2.54mm Pitch Plug and Socket with Cable – 5 Pcs.
- 30cm in length
- The 26AWG cable size.
- Sturdy and long-lasting.
- Simple and safe to install.
- RoHS compliant.
4 Pin JST XH 2.54mm Pitch Plug and Socket with Cable – 5 Pcs.
- Item of Product: KCD4-0312-21
- Panel Mount: 22 x 30 mm in diameter
- Solder pin is the method of contact.
- Install Method: Buckle
- Type of Lamp: LED
4 Pins 3.96mm Pitch JST-VH Connector With Housing (Pack of 10)
3.96 mm is the pitch.
1 contact point pin’s width is approximately 1.1 mm.
Good quality plastic.
Terminals coated with nickel.
Perfect for radio-controlled servos, rechargeable battery packs, etc.
Load more products
Loading...