Showing 625–636 of 4090 results
5MP Rpi 3/4 B camera module with cable
Original price was: ₹550.00.₹450.00Current price is: ₹450.00.- Resolution: 5 MP
- Interface Type: CSI(Camera Serial Interface)
- Dimensions: 25x23x8 (LxWxH) mm
- Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
- Fully Compatible with Raspberry Pi 3 and 4 Model B
- Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
5PIN RMC WIRE (FEMALE TO FEMALE) -30CM
Original price was: ₹150.00.₹135.00Current price is: ₹135.00.
5S 15A 18650 Li-ion Lithium Battery BMS Charger Protection Board for 18V 21V Battery
Original price was: ₹309.00.₹235.00Current price is: ₹235.00.- Voltage used for charging: 21V
- 56 A is the charging current.
- Current for continuous discharge: 15 A
- 50/55/60 A overcurrent protection
- Delay in overcurrent protection: 20/25/30 mS
- Power consumption for a single part since: 30 uA
- Voltage range for single section discharge detection: 2.75–2.85V
- Voltage range for over discharge recovery: 2.90–3.20V
5V 0.2A 3007 Cooling Fan for Raspberry Pi and 3D Printer
Original price was: ₹141.00.₹99.00Current price is: ₹99.00.- Ideally suited for the extruder
- Silent Performance
- Extremely low usage of current
- Simple to connect to and install.
5V 0.2A Raspberry Pi Cooling Fan
Original price was: ₹250.00.₹117.00Current price is: ₹117.00.- This fan can be used with all the models of Raspberry Pi 3, 2.
- Connector: 2 pin Rated
- Voltage: DC 5V Current: 0.2A
5V 1 Channel Relay Module
Original price was: ₹85.00.₹55.00Current price is: ₹55.00.- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- Power supply indicator lamp
- Control indicator lamp
- Triode drive, increasing relay coil
5V 1 Channel Without Light Coupling Relay
Original price was: ₹101.00.₹75.00Current price is: ₹75.00.- Driveability of the 8550 transistor.
- bolt holes that are fixed for simple installation.
- It features eight relay status indicator LEDs (Red), one relay status indicator led (Power LED, Green).
- Interface for control of relays via single-chip IO.
- High-level release, low-level suction closure.
- Three simple lines that are easy to use.
5V 1A Single Pin DC Adapter
Original price was: ₹190.00.₹150.00Current price is: ₹150.00.- Input – 100-240 VAC 50/60Hz
- Output Type – DC
- Output – 5Volts 1Amp
5V 2 channel USB PC Intelligent Control Relay Module
Original price was: ₹625.00.₹575.00Current price is: ₹575.00.- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military grade PCB board production.
5V 2A ERD Adapter with Micro USB cable
Original price was: ₹250.00.₹169.00Current price is: ₹169.00.- Output Voltage : 5V DC,
- Max Current: 2A,
- USB to microUSB
- Cable Length: ~1.5m
- High quality – Stabilized Output with Low Ripple & Low interference – Short Circuit &
- Overload protection –
- High Efficiency & Low Energy Consumption Compatible with Raspberry Pi 3 Model B / ORPi 2 Model B / RPi B+ / A+
5V 2A Wireless Transmitter Receiver Charging Coil Module
Original price was: ₹800.00.₹672.00Current price is: ₹672.00.- XKT-412 is the model.
- 12 volts is the input voltage.
- 5V is the output voltage.
- 1.2-2 A is the operating current.
- 3mm receiving coil; 5V/1A current output from the receiver
- Usual Distance: 2 to 10 mm
- 1.2-2 A is the operating current.
5V 3A ERD Power Adapter
Original price was: ₹450.00.₹366.00Current price is: ₹366.00.- Output Voltage : 5V DC
- Max Current: 3A USB to microUSB
- Cable Length: ~1 – 1.5m USB to microUSB
- Switch Cable Length: 1.5m
- It is compatible with Jetson Nano 2gb and 4gb boards as well
