Showing 829–840 of 2404 results
Shop
DFRobot FireBeetle ESP32-E IoT Microcontroller with Header (Supports Wi-Fi & Bluetooth)
- Operating Voltage: 3.3V.
- Input Voltage: 3.3V~5.5V.
- Support Low-Power: 2mA.
- Support USB Charging.
- GDI Display Port, easy to connect.
DFRobot Gravity Air Pressure Sensor (15-700kPa) – I2C – MPX5700AP
- Detection of physical quantities: Air pressure.
- Working voltage: 3.3~5.5V DC.
- Power dissipation: 0.06W(5)V.
- Epoxy resin integral components.
- Maximum error of 2.5%.
DFRobot Gravity DHT22 Temperature & Humidity Sensor
- 5V is the supply voltage.
- Variation Range: -40 to 80°C / Resolution: 0.1°C / Error: <±0.5°C
- Range for Humidity: 0–100% RH, resolution: 0.1% RH, error: ±2% RH
- Map of wiring: VCC, GND, S
- Dimensions: 38 x 20 mm
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
DFRobot Gravity ENS160 Air Quality Sensor
- Power Supply Voltage: 3.3 V~5.5 V
- Working Current: 29 mA
- Interface Mode: I2C
- Less than 3 minutes warm-up time, get data faster.
- Built-in algorithm, more accurate output.
DFRobot Gravity Gesture & Touch Sensor
- Brand: DFRobot
- Product: Gravity Gesture & Touch Sensor
- Operating Voltage: 3.3V~5V
- Operating Current: 56.3mA
- Current in Sleep Mode: 40uA
- Communication: UAR For bulk and B2B enquiries kindly mail us at ibots.in
DFRobot Gravity Heart Rate Monitor Sensor for Arduino
- Name: DFRobot
- Product: Arduino Gravity Heart Rate Monitor Sensor; Recommended
- Input Voltage (Vin): 3.3 – 6 V.
- Output Voltage: 0/Vin (digital), 0–Vin (analogue)
- <10mA of operating current
Note:
- Within India, 3 – 4 days lead time with 100% advance
- For imports, 15 days lead time with 50% advance
DFRobot Gravity I2C Oxygen Sensor
- Detection of Gas: oxygen
- Operating Voltage: 3.3 to 5.5V DC
- Output Signal: I2C output
- Measurement Range: 0~25%Vol
DFRobot Gravity Lab Grade Analog ORP Sensor Meter For Arduino
- Product: DFRobot Gravity Lab Grade Analog ORP Sensor
- Module Power: +5.00V
- Measuring Range:- 2000mV—2000mV
- Suitable Temperature: 5-70℃
- Accuracy:±10mv (25 ℃) FOR BULK B2B ENQURIES MAIL US @ibots.in
DFRobot Gravity SGP40 Air Quality Sensor
- Power Supply: 3.3V~5V
- Operating Current: 2.6mA
- Preheat Time: 10S
- Response Time: 2S
- Communication: I2C
DFRobot Gravity: I2C Ozone Sensor (0-10ppm)
- Detection Gas: Ozone
- Working Voltage: 3.3 ~ 5.5V DC
- Interface: Gravity-4Pin
- Output Signal: I2C output
- Measuring Range: 0 ~ 10ppm
- Resolution: 0.01ppm (10ppb)
- Warm-up Time: ≤3 minutes
- Response Time: ≤90 seconds
- Recovery Time: ≤90 seconds
- Working Temperature: -20 ~ 50 ℃
- Operating Humidity: 15 ~ 95% RH (non-condensing)
DFRobot Gravity: MEMS Gas Sensor (CO, Alcohol, NO2 & NH3) – I2C – MiCS-4514
- Operating Voltage: 3.3~5.5V DC
- Power Dissipation: 0.45W(5V)
- Output Signal: I2C (0~3V)
- Working Temperature: -30~85℃
- Working Humidity: 5~95% RH(No condensation)
- Storage Temperature: -40~85℃
- Lifespan: >2 years (in the air)
- Circuit Board Size: 27mm* 37mm
- Mounting Hole Size: inner diameter 3.1mm/ outer diameter 6mm
Digi XBee3 2.4GHz ZB3.0 PCB Antenna
- Serial Data Interface: Uart, Spi, I2c.
- Configuration Method: API Or At Commands, Local Or Over-the-air.
- Frequency Band: ISM 2.4 GHz.
- Form Factor: Micro, Through-hole, Surface Mount.
- Interference: Immunity Dsss (Direct Sequence Spread Spectrum).
- Adc Inputs: (4) 10-bit Adc Inputs.
- Digital I/o: 15. FIR BULK B2B ENQUIRIES MAIL US @ibots.in
Load more products
Loading...