Showing 1–12 of 80 results
Sensors
12mm GL12528 Light Sensitive Photoresistor LDR (2Pcs)
- 12 mm in diameter
- Two pins in total.
- Mounting style: PCB Through Hole
- The maximum operating temperature is around +70˚C.
- Resistance to dark: 1–20 MΩ
- Peak spectrum: 560 nm
- Maximum DC voltage is 250 V.
- 200 mW maximum wattage
- Ten Lux light resistance: 10–20 KΩ
- 2 MΩ of dark resistance
- Illumination resistance: three
- 20 ms for rise and 30 ms for fall in response times.
2.2inch Flex Sensor
- Model:FLEX-SENSOR-2.2
- Weight:30.00g
5 Way IR Sensor Array – TCRT5000L
1) High-Quality Tracker Sensor
2) The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced.
3) Distance between each IR Sensor: 15mm
4) Uses 5 sensors for best resolution
5) Great useful in building fast line following and grid navigating robots
6) Comes with easy to use digital outputs with a direct connection to microcontrollers
7) The array has mounting holes of 3mm diameter for easy mounting
5A range Current Sensor Module ACS712
- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
5mm LDR (Pack of 10)
- 5 mm in diameter
- Two pins in total.
- Mounting Type: PCB Through Hole
- The maximum operating temperature is around +800°C.
- Resistance to dark: 1–20 M ohm
8 Channel IR Sensor Array Infrared Detection Module
- 8 IR Sensors with High Range
- Operating voltage: 3.3 to 5V
- Current supply: 100mA
- Output format: 8 digital I/O compatible signal
- Optimal sensing distance: 3 mm
- Maximum recommended sensing distance: 6 mm
- Distance between each IR Sensor: 15mm
AD8232 ECG Monitor Sensor Module
- Designed to extract, amplify, and filter small biopotential signals.
- Leads-Off Detection.
- Shutdown Pin.
- LED Indicator.
- Analog Output.
- 5 mm Jack for Biomedical Pad Connection.
ADXL335 Module 3-axis Analog Output Accelerometer
- LDO voltage regulator on board
- Interfaceable with a microcontroller operating at 3V3, or 5V.
- Double or Tap Tap Detection
- Free-Fall Identification
- Analogue output
- Integrated linear LDO voltage regulator with extremely low noise
- Onboard filters that are integrated and lower noise levels from High-current electronics and motors
- Energise LED
ADXL345 Tripple Axis Accelerometer Board
- Voltage of supply: 3.3 V/5 V.
- Interface Type: SPI and I²C.
- ±2g, ±4g, ±8g, ±16g is the sensing range.
- Sensitivity: 34.5 LSB/g for Z, 31.2 LSB/g for Y, and 28.6 LSB/g for X.
- Ultra Low Power: 0.1µA in standby at 2.5V and 40µA in measuring mode.
- Fall-Free Detection.
- Double or Tap Tap Detection.
Analog Sound Sensor Microphone Module for Arduino
- Detectable sound signal size
- Built-in filter-rectifier circuit, DC signal output
- Good sensitivity, built-in amplifier circuit, adjustable gain
- Voltage signal for sound intensity can be obtained by AD conversion
- Analog voltage signal output, signal amplitude VCC/2
- Compatible for Arduino sensor interface.
AS608 Optical Fingerprint Sensor Module
Features:
- Integrated image collecting and algorithm chip together, ALL-in-One.
- The fingerprint reader can conduct secondary development, can be embedded into a variety of end products.
- Low power consumption, low cost, small size, excellent performance.
- Resolution: 500dpi
- Fingerprint image entry time: <1.0 seconds
- Window area: 15.3×18.2MM
- Communication Interface: USB/UART
ASAIR DHT-11 Digital Temperature And Humidity Sensor
- Temperature and Humidity Sensing: The DHT11 sensor can measure both temperature and humidity with high accuracy.
- Single-Wire Interface: It features a single-wire digital interface, simplifying its integration with microcontrollers and other electronic devices.
- Temperature Range: The temperature measurement range of the DHT11 sensor is from 0°C to 50°C.
- Temperature Accuracy: It has an accuracy of ±2°C, providing reliable temperature readings within its specified range.
- Humidity Range: The humidity measurement range is from 20% to 80% RH (Relative Humidity).
- Humidity Accuracy: The sensor offers an accuracy of ±5% RH, ensuring precise humidity measurements.
- Applications: Due to its accuracy and ease of use, the DHT11 sensor is suitable for various applications such as weather stations, greenhouses, HVAC (Heating, Ventilation, and Air Conditioning) systems, and any project requiring temperature and humidity monitoring.
- Cost-Effective: The DHT11 sensor is known for its affordability while still maintaining high performance, making it an attractive choice for hobbyists, students, and professionals alike.
Load more products
Loading...